Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Motor & Opener in Tempe: What to Know First
We provide independent FAAC gate motor and opener service in Tempe, with most repairs completed same-day and a written price delivered before any work starts. Typical turnaround for a diagnosed FAAC motor issue is two to four hours on-site, including full cycle testing and documentation. We don’t replace a 415 or 770 operator just because another company couldn’t source the control board.
This page is for Tempe homeowners who already know they have a FAAC system and need someone who can name the part, name the price, and leave a record of what was done. Whether your gate is stuck open on a Saturday night or the arm is clicking but not pulling, we answer live at (623) 323-3849, 24 hours a day.
How FAAC Products Fail - and How We Fix Them
- FAAC 415 swing-gate operator: seized worm gear in the reduction box. The 415’s cast aluminum gearbox housing expands and contracts through Tempe’s 110°F summer afternoons and 45°F winter nights, eventually wallowing out the bearing seats. The motor runs but the output shaft doesn’t turn. We pull the gearbox, measure shaft runout, and either rebuild with OEM FAAC worm and wheel sets or source a quality aftermarket gearbox when FAAC lead times stretch past two weeks. We photograph the gear wear pattern before we quote the repair.
- FAAC 770 slide-gate motor: thermal overload shutdown on long runs. The 770’s fan-cooled design works fine in moderate climates, but on south-facing Tempe driveways with no shade, the motor hits its thermal cutout after three or four consecutive cycles. We check the run capacitor first, then verify the gate isn’t dragging on a warped track or debris-filled guide roller. Often the fix is a capacitor upgrade and track realignment, not a motor replacement.
- FAAC 402 CBC control board: intermittent open/close commands from voltage spike damage. The 402’s logic board sits in an unvented enclosure on many older Tempe installations, and monsoon-season lightning strikes or utility switching transients fry the relay outputs. We test each output with a load simulator, replace the board with a current-production 402 SBS or a compatible aftermarket unit, and add a surge suppressor at the terminal strip. Under Clause 4, you get a photo of the board serial number and the suppressor installation.
- FAAC 746 articulated arm: cracked cast elbow at the motor mount. The 746’s geometry puts bending stress on the aluminum elbow where the motor bolts to the arm, and gates heavier than 350 pounds or with misaligned posts accelerate fatigue cracking. We mag-check the casting, replace with a FAAC elbow or a machined steel equivalent when the gate weight warrants it, and reset the limit switches so the arm isn’t pulling against mechanical stops.
- FAAC E024 external receiver: range collapse after battery degradation in the remote. Not strictly a motor failure, but we get calls in Tempe’s Papago Buttes area where the gate won’t respond from the street. The E024’s sensitivity drifts as the remote’s CR2032 drops below 2.8 volts, and homeowners think the motor is dead. We test signal strength at the receiver antenna, replace remotes or reprogram rolling-code pairs, and log the new remote serial numbers in your job record.
Our FAAC Gate Motor & Opener Process
- 1
Call intake with model verification. We ask for the FAAC model number on the motor nameplate and the symptom sequence. If you don’t have the model, we pull it from our photo database of past Tempe jobs or read it on arrival.
- 2
On-site diagnostic with load testing. We cycle the gate under no-load and normal-load conditions, measure motor current draw with a clamp meter, and check limit switch repeatability. Everything goes in the written record.
- 3
Parts decision: OEM, available aftermarket, or repair. For a 415 or 770, we stock common FAAC wear parts. For obsolete 580 or 390 series, we source compatible aftermarket controllers or machine adapters. We explain the warranty difference and the price difference before you decide.
- 4
Repair and real-time adjustment. We set force limits to FAAC spec, not “whatever works.” For slide gates, we verify the clutch releases at 400 N or per the installation manual. For swing gates, we check the hydraulic bypass on FAAC 402 units.
- 5
Cycle testing and photo documentation. Twenty full open-close cycles minimum, with amperage logged at start and finish. You get a photo log of every adjustment, every part number, and the final limit switch positions.
- 6
Written invoice and 365-Day Done Right Promise activation. The price matches the written quote. The promise covers parts and labor with no expiration within the year. Name what you found. Name what it costs. Leave the gate better than you met it.
Before
AfterWhat FAAC Gate Motor & Opener Costs in Tempe
These are real ranges for FAAC work we’ve done in Tempe, not teaser prices that balloon on site.
| Service | Typical Range | What Moves the Price |
|---|---|---|
| FAAC control board replacement (402/746 series) | $340 - $580 | OEM vs. aftermarket board; whether enclosure needs rewiring |
| FAAC 415/770 motor gearbox rebuild | $280 - $460 | Gear wear severity; shaft straightening needed |
| FAAC articulated arm replacement (746) | $420 - $720 | Single vs. dual arm; post bracket condition |
| FAAC slide-gate track realignment + roller service | $180 - $320 | Track length; roller quantity and type |
| FAAC system diagnostic with written estimate | Free | No charge; estimate valid for 30 days |
Every price is written and handed to you before we pick up a tool. If we find something unexpected, we stop, explain, and get your sign-off on a revised written price. No invoice has ever exceeded its written quote at Vance Gate Repair Tempe.
Call (623) 323-3849 for a free estimate. We’ll ask the right questions so the technician shows up with the right parts already in the van.
Why Tempe Homeowners Call Vance Gate Repair Tempe for FAAC Work
We service nine automation brands, including LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so we have no incentive to steer you away from your FAAC system toward something else. Adrian Vance started this company in 2014 after years of commercial access-control work, and the documentation habit stuck: every residential job gets the same wiring diagrams, photos, and written records that commercial clients demanded.
Our 365-Day Done Right Promise means if a FAAC repair isn’t right, we make it right with no argument and no fee. A live person answers (623) 323-3849 at any hour, and we dispatch background-checked, uniformed technicians with their name and photo sent to you before arrival. Since 2014, we’ve documented over 22,000 gates with written prices before work started and photo records when we left.
FAQs
FAAC’s original equipment warranty expires after two years from installation, so most Tempe systems we see are already outside that window. For newer units, as an independent FAAC service provider, we use FAAC OEM parts where possible to preserve any remaining coverage, and we note serial numbers and install dates in your record. Call (623) 323-3849 and we’ll check your warranty status before quoting.
Most FAAC motor repairs are completed in two to four hours on-site, including diagnostic, repair, and full cycle testing. If we need to order a specific FAAC part not in our Tempe inventory, we’ll tell you the lead time and secure the gate safely before we leave. Same-day completion is typical for control boards, capacitors, and limit switch issues.
We repair FAAC operators when the gearbox, control board, or arm can be restored to reliable function for less than 60 percent of replacement cost. For 415 and 770 series with obsolete boards or cracked housings, we’ll quote both paths in writing. The decision is yours, not ours, and we stock parts for nine brands so we don’t need to sell you a new system to make the visit profitable.
We carry 415 and 770 gearboxes, 402 control boards, 746 arm assemblies, limit switch kits, and run capacitors in our Tempe-area inventory. For older FAAC series or specialized accessories, we source from our network with typical two-day turnaround. We check parts availability during the call intake so the technician doesn’t arrive empty-handed.
Yes. On any FAAC motor or opener job in Tempe, we verify the 110V supply, ground integrity, and photo-eye alignment per UL 325 standards. We install or adjust safety edges, loop detectors, and intercom integration as part of the scope, and we test every safety device under load before we leave. The photo record includes voltage readings and safety device function checks.
Written by Adrian Vance, Owner, Vance Gate Repair Tempe at Vance Gate Repair Tempe, serving Tempe and nearby areas.