Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFAAC Gate Installation in Tempe: What to Know First
We install FAAC swing and slide gate operators in Tempe as an independent service provider, with most residential jobs measured, quoted, and scheduled within 48 hours of your call. A typical FAAC 415 or 770 series installation runs between $2,800 and $4,600 depending on gate material, existing electrical, and whether we’re retrofitting an old bracket or starting fresh. We don’t start any work until you have a written price in hand and agree to it.
This page is for Tempe homeowners who already own a FAAC operator or are weighing one against other brands and want to know what the installation actually involves, what it costs, and who’ll stand behind it. If that’s you, call (623) 323-3849. A live person answers, even at 2 a.m.
How FAAC Products Fail - and How We Fix Them
- FAAC 415 Low-Voltage Swing Arm - Control Board Capacitor Swelling The 415’s control board runs hot in Tempe’s 115°F summer garage environments, and we’ve replaced dozens where the main capacitor has swelled enough to push the gate into “safe mode” (three beeps, no movement). We pull the board, photograph the capacitor condition for your record, and install either an OEM FAAC replacement or a commercial-grade equivalent rated for 85°C ambient. Under the Haven Standard, you get the photo and the part number before we close the panel.
- FAAC 770 In-Ground Swing Operator - Water Ingress in the Motor Block The 770’s buried motor housing has a vented drain design that works fine in dry climates until Tempe’s August monsoon runoff pools at the base. We find corrosion on the armature windings that starts as intermittent reversing and ends with a seized motor. Our fix: pull the operator, inspect the housing seal, replace the motor if the winding resistance reads outside 12-18 ohms, and reset the mechanical stops with a torque wrench to FAAC’s 45 Nm spec. We document the resistance reading and the new stop position.
- FAAC 844 Slide Gate Operator - Rack Gear Misalignment from Thermal Expansion The 844’s nylon rack gear expands roughly 3/16 inch per 10 feet across a 40°F Tempe temperature swing, enough to skip teeth and throw the limit switches. We don’t just realign; we calculate the rack gap at installation temperature and leave a thermal expansion note in your job file so the next technician knows why the gate was set with a slightly wider tooth engagement than the manual suggests.
- FAAC S418 Residential Swing - Limit Switch Drift After Power Events The S418’s magnetic limit switches are sensitive to voltage sag during Phoenix-area summer brownouts. The gate “forgets” its open position and slams the mechanical stop. We install a surge protector on the low-voltage side, recalibrate the limits with a digital multimeter reading the Hall sensor output, and photograph the final voltage at both limit positions. Most Tempe electricians don’t touch low-voltage gate logic; we do.
- FAAC E045 Pedestrian Lock - Solenoid Burnout from Continuous Duty The E045 is rated for intermittent duty, but Tempe homeowners with frequent foot traffic (college rentals near ASU, multi-generational homes) sometimes cycle it 200+ times daily. The solenoid coil overheats and shorts. We replace with a continuous-duty aftermarket solenoid where the application demands it, or recommend the FAAC E124 heavy-duty lock instead. Either way, we write down the duty-cycle math and leave it with you.
Our FAAC Gate Installation Process
- 1
Site measure and electrical survey. We check your gate’s weight, width, and swing geometry against FAAC’s load charts. We verify whether you have 110V within 25 feet or need a conduit run. The price you get includes both scenarios, spelled out separately.
- 2
Parts decision: OEM or qualified aftermarket. For FAAC operators still in production, we quote OEM first. For discontinued lines like the early 400 series, we source commercial-grade aftermarket from our Phoenix warehouse supplier and tell you exactly what’s in the box. No surprises.
- 3
Written quote, signed before work starts. Haven Standard Clause 1: the price is fixed, itemized, and agreed in writing. If we find rot in a wood gate post or a cracked concrete footer during dig, we stop, photograph it, and write a revised scope. Nothing happens without your initials.
- 4
Install and document. We mount the operator, set limits with a digital meter, program remote codes, and test the safety photo-eye at three heights. Adrian Vance or a background-checked, uniformed technician photographs every connection, every setting, and every test result. You get a copy; we file the master.
- 5
Final cycle test and walkthrough. We run the gate through 20 full cycles, check amp draw under load, and show you the manual release procedure. Then we hand you the 365-Day Done Right Promise in writing.
- 6
Cleanup and record delivery. We haul old material, sweep the work area, and leave you with the photo log, the wiring diagram, and the signed warranty card. Name what you found. Name what it costs. Leave the gate better than you met it.
Before
AfterWhat FAAC Gate Installation Costs in Tempe
These are real ranges from jobs we’ve completed in Tempe, not teaser prices that balloon on site.
| Scenario | Typical Range | What Moves the Price |
|---|---|---|
| FAAC 415 swing operator, retrofit to existing gate | $2,800 - $3,400 | Bracket condition, conduit length, need for new photo-eyes |
| FAAC 770 in-ground, new install | $4,200 - $5,800 | Excavation depth, drainage bed, gate material weight |
| FAAC 844 slide operator, residential | $3,600 - $4,800 | Rack length, guide roller condition, existing chain vs. new |
| FAAC S418 with solar option | $3,200 - $4,400 | Panel size, battery bank, trenching for low-voltage cable |
| Access control add-on (keypad, telephone entry) | $680 - $1,400 | Wired vs. wireless, brand compatibility, programming complexity |
Every estimate is free, every price is written, and every job starts only after you agree to the number. Call (623) 323-3849 to schedule a measure.
Why Tempe Homeowners Call Vance Gate Repair Tempe for FAAC Work
We’ve repaired and installed over 22,000 gates since 2014, and a growing share of our Tempe calls are FAAC systems originally installed by builders or pool contractors who didn’t leave documentation. We carry FAAC parts in the van, but we’re not locked to one brand. If your FAAC 770 is discontinued and a LiftMaster LA500 or Ghost Controls TSS1XP fits your gate better, we’ll show you both options in writing. Our technicians are background-checked and uniformed; you get a name and photo before arrival. And if something isn’t right within a year, we make it right. No argument, no fee. That’s the 365-Day Done Right Promise.
Adrian Vance started this company after years on commercial access-control sites, and the habit stuck: every residential gate in Tempe gets the same documentation he’d file for a municipal job. The photo record, the wiring diagram, the written price. It’s not extra. It’s the work.
FAQs
No, installing a FAAC operator does not void a gate manufacturer’s warranty, provided the operator is sized correctly for the gate’s weight and duty cycle. We check your gate manufacturer’s load spec against FAAC’s published capacity before we quote, and we document that match in your job file. If your gate is still under builder warranty, that documentation protects both of us. Call (623) 323-3849 if you want us to review your gate paperwork before we measure.
Most residential FAAC installations are completed in one working day, with the gate operational before we leave. A 770 in-ground system may need a second day if the drainage bed requires cure time. We schedule, we don’t rush. You’ll know the day count before you sign.
Often, yes. If your FAAC operator is a current series with available parts, we quote repair first. For discontinued lines like the 400 series with obsolete control boards, we show you the repair-versus-replace math in writing, including parts availability and warranty length. We don’t steer toward replacement when repair is the honest call.
We stock both. For operators under FAAC’s own warranty period, we use OEM parts to preserve that coverage. For out-of-warranty systems, we may recommend commercial-grade aftermarket if the quality is equivalent and the price difference matters. We name the manufacturer on every part, every time.
Bring it. We offer free second opinions on any written estimate. We’ll review their scope against what we find, point out anything we disagree with, and write our own price if you want it. No charge, no pressure. Haven Standard Clause 1 applies either way: if you hire us, the price is in writing before we start.
Written by Adrian Vance, Owner, Vance Gate Repair Tempe at Vance Gate Repair Tempe, serving Tempe and nearby areas.